mid plate problem plz help!!

Ok im finally ready to put my fox together im running d&d headers and motor plates. The mid plate on the passenger side aint even close to fitting trimming wont help what should i do thanks for the help

gonna have to trim it, wont be much left worth mounting after your done. I'd weld a tab on the plate in a different spot. i even like to put a tap on the top and run spacers through the firewall, tie it into the rollcage............damn stout that way...lets the midplate do its job and distribute the power to the chassis.

In the process of doing this on our smallblock fox mustang, should be able to get some progress pics by the weekend.

cool thanks only thing is im not running a roll cage yet its a street car the way it looks to me trimming it wont work...... big thanks to bob at d&d these hearders are awesome if it wasnt for the mid plate problem it would b smooth sailing

I think you're gonna have to make a new mid plate. Should look similar to this






I trimmed mine to fit the headers first and then the chassis. Actually I made a cardboard template and trimmed it FIRST then transfered it over to the metal plate and then cut/trim...

Thanks that looks good what kind of plate did you cut that out of how thick Just regular sheet metal ?

Big block fox 339 wrote:Thanks that looks good what kind of plate did you cut that out of how thick Just regular sheet metal ?

It started out as a midplate from Bob at D&D but it's a "trim to fit deal" and is one big square with the holes already cut to fit the bolts and dowel pins.

D. Sea wrote:

Big block fox 339 wrote:Thanks that looks good what kind of plate did you cut that out of how thick Just regular sheet metal ?

It started out as a midplate from Bob at D&D but it's a "trim to fit deal" and is one big square with the holes already cut to fit the bolts and dowel pins.

we ran the same set up and had to do the same thing,tried 3 different plates before we got it right,the mid plate was the toughest part of the swap

Thanks for the ideas guys i got my template made gonna make the mid plate tomorrow. I got one more question what kind of mount did yall use due to the mounting holes being so much higher

Big block fox 339 wrote:Thanks for the ideas guys i got my template made gonna make the mid plate tomorrow. I got one more question what kind of mount did yall use due to the mounting holes being so much higher

Why not just utilize the plate you have & cut the passenger-side ear off & re-locate it? That way you retain the bolt & dowel pin holes, and can put the mount holes/tab where you need them..

Just thinking outside the cashbox

I have "L" type brackets that attache to the frame and then bolt to the midplate. Sorry, don't have pictures of those brackets.

Why not just utilize the plate you have & cut the passenger-side ear off & re-locate it? That way you retain the bolt & dowel pin holes, and can put the mount holes/tab where you need them..

Just thinking outside the cashbox [/quote]


Yeah thought about that but the metal for the new one wasn't but 17 buck so I went that route

here is mine but i also had to trim a buch on the pass side for the kooks to work ... i tried to copy Damons deal

Good picture Nick,

If you guys look really close, you can see the brackets that are bolted THROUGH the frame. One day while Bill was over helping with the anti-roll bar, he tig welded some nuts on the backside of the brackets. Makes installation MUCH easier


Edit:

339,

You may have to trim a little bit more on the drivers side to clear the steering shaft. You won't know until you get it test fitted in the car.

Thanks for the pic Mr. bruno... ive got those same L brackets but i dont think mine are gonna b high enough im just gonna fab whatever i need to make it work i hope to stick the motor and tranny in this weekend!!!!

bruno wrote:

here is mine but i also had to trim a buch on the pass side for the kooks to work ... i tried to copy Damons deal

No kidding ,you had to trim a bunch off of it :king:Looks like you got hammer happy on the fire wall too