You guys ever lift a complete BBF and glide by the carb pad?
Page 2 of 2 • Share •
Page 2 of 2 • 
1, 2
Re: You guys ever lift a complete BBF and glide by the carb pad?
Wheelie58 on August 9th 2011, 11:21 pm
David Cole wrote:I bought one of these a little while back. Worth double what it cost! I have used it twice. Last time was to put the 598 in my Bird. Fully assembled and with a JW case (heavy!) glide attached. It combines a lift plate with a load leveler. You can tilt the complete assembly almost to 45° in either direction or level it even with much more weight on one end. $70
http://kaizen.homestead.com/Loadlevelingliftplate.html
That is a nice link, David.
It shows some test data about the loads required to fail their lift device.
Cool....
Keith
Wheelie58- Posts: 882
Join date: 2009-08-08
Location: Alpharetta, GA 
Re: You guys ever lift a complete BBF and glide by the carb pad?
bbf-falcon on August 10th 2011, 3:26 am
WOW 
bbf-falcon- Posts: 5225
Join date: 2008-12-03
Location: Jackson, Ohio -
Re: You guys ever lift a complete BBF and glide by the carb pad?
jbozzelle on August 10th 2011, 1:17 pm
Thanks guys. I got it dropped in last night.
jbozzelle- Posts: 2174
Join date: 2009-08-10
Age: 37
Location: New Orleans -
Re: You guys ever lift a complete BBF and glide by the carb pad?
bruno on August 10th 2011, 1:34 pm
Dan Hobbs has some test data on the piece we used also 
_________________
THXS TO ALL MY SPONSORS
www.bfevansraceparts.com
www.evansracingengines.com
JET BOAT BOB
DAN " THE STICKER MAN " HOBBS ...AKA >>>> 56TBIRD
bruno- Moderator
- Posts: 7778
Join date: 2008-12-02
Age: 39
Location: MILLBROOK , AL. -
Re: You guys ever lift a complete BBF and glide by the carb pad?
schmitty on August 10th 2011, 10:33 pm
I made my own out of 1/4" plate and I set my engine, trans, and heavy 205 cast iron T/C in all in one piece. 
_________________
Big Daddy has spoken
Proud founder of the Truck Mafia
Definately in favor of God and guns
schmitty- Moderator
- Posts: 2896
Join date: 2008-12-02
Age: 41
Location: Big Daddy in the House -
Re: You guys ever lift a complete BBF and glide by the carb pad?
IDT-572 on August 11th 2011, 8:08 am
schmitty wrote:I made my own out of 1/4" plate and I set my engine, trans, and heavy 205 cast iron T/C in all in one piece.
Now that's a test.................
I have always set mine that way too until this last engine where I modified my manifold..............
IDT-572- BBF CONTRIBUTOR
- Posts: 2643
Join date: 2008-12-02
Age: 51
Location: Shelbyville Tn. -
Re: You guys ever lift a complete BBF and glide by the carb pad?
'65 T-BOLT on August 11th 2011, 8:12 am
I still use the redneck eastern mountain william way! chain!
'65 T-BOLT- Posts: 1409
Join date: 2009-08-28
Age: 41
Location: Hagerstown,Maryland -
Re: You guys ever lift a complete BBF and glide by the carb pad?
BigBlockRanger on August 11th 2011, 8:21 am
Yes.
BigBlockRanger- Posts: 279
Join date: 2008-12-02
Age: 41 -
Page 2 of 2 • 1, 2
Page 2 of 2
Permissions in this forum:
You cannot reply to topics in this forum