A460 deal
Page 1 of 1 • Share •
Re: A460 deal
bruno on January 5th 2012, 9:47 pm
nice #s Lem
_________________
THXS TO ALL MY SPONSORS
www.bfevansraceparts.com
www.evansracingengines.com
JET BOAT BOB
DAN " THE STICKER MAN " HOBBS ...AKA >>>> 56TBIRD
bruno- Moderator
- Posts: 7784
Join date: 2008-12-02
Age: 39
Location: MILLBROOK , AL. 
Re: A460 deal
schmitty on January 5th 2012, 9:50 pm
Very nice. I'll bet it'll do some long smoky burnouts too. 
_________________
Big Daddy has spoken
Proud founder of the Truck Mafia
Definately in favor of God and guns
schmitty- Moderator
- Posts: 2896
Join date: 2008-12-02
Age: 41
Location: Big Daddy in the House -
Re: A460 deal
56Tbird on January 5th 2012, 11:37 pm
I've seen the burnouts.....Impressive,but the wheelies are even more impressive!!
56Tbird- BBF CONTRIBUTOR
- Posts: 3679
Join date: 2008-12-02
Age: 53
Location: Hawesville,Ky. -
Re: A460 deal
Wheelie58 on January 6th 2012, 12:01 am
It is sure hard to beat the power per dollar with a well prepped A460 Trick Flow setup. I bet that mill would be over 900 on torque if you could catch it at 5500 or so. Good work up there...guys!
Keith
Keith
Wheelie58- Posts: 882
Join date: 2009-08-08
Location: Alpharetta, GA -
Re: A460 deal
bruno on January 6th 2012, 7:41 am
is this george's old/new build ?
_________________
THXS TO ALL MY SPONSORS
www.bfevansraceparts.com
www.evansracingengines.com
JET BOAT BOB
DAN " THE STICKER MAN " HOBBS ...AKA >>>> 56TBIRD
bruno- Moderator
- Posts: 7784
Join date: 2008-12-02
Age: 39
Location: MILLBROOK , AL. -
Re: A460 deal
Lem Evans on January 6th 2012, 8:47 am
bruno wrote:is this george's old/new build ?
Yes it's the famous George deal....I was looking thru some of my stuff and ran accross this dyno sheet from 2010. This is one of the pulls when it was on Q16 gas before it recieved the methanol setup. Phillip was nice enough to show up with his t.r. top and QFT 1450s.
Lem Evans- Posts: 4073
Join date: 2008-12-03
Location: Livermore , Ky -
Re: A460 deal
Lem Evans on January 6th 2012, 8:50 am
bbf-falcon wrote:What compression Lem? Nice #'s
It's been almost 2 years but I'm sure it was 14.5:1 ish.
Lem Evans- Posts: 4073
Join date: 2008-12-03
Location: Livermore , Ky -
Re: A460 deal
Lem Evans on January 6th 2012, 8:53 am
Wheelie58 wrote:It is sure hard to beat the power per dollar with a well prepped A460 Trick Flow setup. I bet that mill would be over 900 on torque if you could catch it at 5500 or so. Good work up there...guys!
Keith
Good catch....yes it showed more tq. when we were pulling it lower. It did not quite get to 900 lbs ft but it was 890ish as best as I can remember.
Lem Evans- Posts: 4073
Join date: 2008-12-03
Location: Livermore , Ky -
Re: A460 deal
Lem Evans on January 6th 2012, 8:58 am
schmitty wrote:Very nice. I'll bet it'll do some long smoky burnouts too.
not as much as your 6.7
Lem Evans- Posts: 4073
Join date: 2008-12-03
Location: Livermore , Ky -
Page 1 of 1
Permissions in this forum:
You cannot reply to topics in this forum