Re: 1995 F150 pro Street project thread

[posford]

The truck's lookin' good Alan. I have the same air compressor and love it. Plenty of air and it's not too noisy.

[HorsinAround]

In a couple weeks, anyone will be able to order 2-1/4 into 4 headers for their 80's and 90's ford big block trucks. A big thanks to Maddog headers for working with me. I took my rod up to be the prototype..

[D. Sea]

Alan,

Nice project and nice work. I see a lot of Truck Puller engineering. Brings back memories when Dad and I used to truck pull   

[IDT-572]

Alan,

Nice project and nice work.  I see a lot of Truck Puller engineering.  Brings back memories when Dad and I used to truck pull    

I wish you would get that dog a water bowl...............  

[HorsinAround]

[bbf-falcon]

Great work Alan.  

[f250mike]

It's already looking fast  

[bluef100fe]

Alan, just a little warning... That shifter you have installed in your picture is not a good match for the detents of a c6 valve body... I had one transmission that had a short lived life because of that shifter.. I got a turbo action shifter after that mishap.. they come with a dedicated gate plate and shifter arm for the c6... It's expensive but worth every penny... Truck is really starting to look like something... Keep up the good work

[jones]

Alan, just a little warning... That shifter you have installed in your picture is not a good match for the detents of a c6 valve body... I had one transmission that had a short lived life because of that shifter.. I got a turbo action shifter after that mishap.. they come with a dedicated gate plate and shifter arm for the c6... It's expensive but worth every penny... Truck is really starting to look like something... Keep up the good work

Is there any other C6 shifters that work well?

[HorsinAround]

Progress has been slow, but here is a few updates.







Also Cody, I abandoned the B&M and went with a Hurst pistol grip quarter stick. Hopefully it will work better than the B&M Mega

[schmitty]

Keep after it Alan, it looks killer.

[droppedf100]

Truck looks good man. Was your motor in the stock location when you had the headers built?

[jones]

Truck looks good man. Was your motor in the stock location when you had the headers built?

I certainly hope so! They was sold to me from maddog as stock location headers. If they where based off this truck I'm going to have problems with the steering shaft. I have been told that a 3" body lift will give me some clearance though. I don't like body lifts.

[HorsinAround]

Yes motor was in the stock location.

Here is a few update pictures.

[bluef100fe]

Alan, I have no experience with the hurst shifter... Hopefully it's better than the megashifter... Truck is looking good..

[69F100]

Alan I pull the grill and head lights and grill support out of my 95 F350 to replace the passage side fender. I looked and don't see how to make the grill and support removable like the grill in my Ranger. The way you have to go about pulling the grill, head lights, and support with out adding to it to make it come out as 1 unit. But on good thing about the way yours will be you won't have batteries to pull and hard to get to place to get the nuts off of the corner/blinker lights. The truck is looking good.

Jim

[cool40]

Looking good! Is that a belt drive fuel pump?

[f250mike]

Hey Alan,
Is there a date for the maiden voyage??
I'm guessing Bunker Hill will be your test track??
If I'm welcome, I'd like to come help/watch or whatever.

[HorsinAround]

Looking good! Is that a belt drive fuel pump?

Yes, it is a fuel pump. I am planning to do the initial start on gas, so I have a carb mounted right now. Once the rings are seated I'll install the Killer Ron's terminator injection system.

Hey Alan,
Is there a date for the maiden voyage?? No, I wish, but no.. My goal is to paint it this May. But it may not go down the track until after my daughter's wedding and a business trip in June.
I'm guessing Bunker Hill will be your test track?? Yes, Bunker is where I am planning to run most.
If I'm welcome, I'd like to come help/watch or whatever.

You bet. Welcome anytime.

Weighed the truck last night on a set of 4 corner scales and was happy to see the results. My goal was 3000 to 3200. She weighed in at 3050. Once I add the wheelie bars and fuel tank she should be 3150.

[cool40]

Im not sure how high in relation to the pump you plan to mount the fuel tank but the belt pumps like being mounted lower if possible. Just something to remember in case you run into fuel starvation issues.

[HorsinAround]

Im not sure how high in relation to the pump you plan to mount the fuel tank but the belt pumps like being mounted lower if possible. Just something to remember in case you run into fuel starvation issues.

Thanks, I am concerned about that as well. I spent several hours playing with the alternator and fuel pump mounts and this was all I could come up with. I designed my own fuel cell that will sit up high in front and wrap around the core support so I am hoping this will prevent fuel starving. I got the tank finished up Sunday and hope to get it installed this weekend.

[HorsinAround]

Got a little more done on the rod. This weekend I'll have the anti-roll bar installed and the aluminum tonneau cover done.

[schmitty]

Looking awesome Alan!!!

[460pulling]

Nice work. Your truck is really coming along now. I think you will be happy once it is complete.

[HorsinAround]

Thanks. We are nearing the end. My last night with the second job is Wednesday, and after next week's business trip, I will have a lot more time to get the turd done! I think I am less than a month away now.

[Sponsored content]