Foxbody Front Exit Headers

View previous topic View next topic Go down

Foxbody Front Exit Headers

Post  Race Ready Fabrications on August 7th 2016, 10:47 pm

Fox body front ext headers. 3/8" thick flanges. 2-1/8" to 2-1/4" step. 4" collector
Tubes 1 and 5 have 1/4" NPT bungs. Will require an oil filter adapter. Painted with some slight rust
$550 shipped
Call/text for more info 812-568-1491

[/[/[/
avatar
Race Ready Fabrications

Posts : 611
Join date : 2010-04-19
Age : 36
Location : Chandler, IN

View user profile

Back to top Go down

Re: Foxbody Front Exit Headers

Post  jbozzelle on August 8th 2016, 8:23 am

Brian, Did you make these?  How far down in the chassis was the engine located?  What k-member, rack setup was used? Just curious how they'd fit in my chassis...

jbozzelle

Posts : 3341
Join date : 2009-08-10
Age : 43
Location : New Orleans

View user profile

Back to top Go down

Re: Foxbody Front Exit Headers

Post  Race Ready Fabrications on August 8th 2016, 9:18 am

jbozzelle wrote:Brian, Did you make these?  How far down in the chassis was the engine located?  What k-member, rack setup was used?  Just curious how they'd fit in my chassis...

Yes I built these. I can get some measurements of where the motor is sitting. This is my k member built on my jig with a flaming river rack and shaft that I built (nothing fancy).
avatar
Race Ready Fabrications

Posts : 611
Join date : 2010-04-19
Age : 36
Location : Chandler, IN

View user profile

Back to top Go down

Re: Foxbody Front Exit Headers

Post  dr's wife racing on August 8th 2016, 10:07 am

What head.
avatar
dr's wife racing
BBF CONTRIBUTOR
BBF CONTRIBUTOR

Posts : 1590
Join date : 2009-08-20

View user profile

Back to top Go down

Re: Foxbody Front Exit Headers

Post  Race Ready Fabrications on August 8th 2016, 11:47 am

dr's wife racing wrote:What head.

Standard CJ, I ran them on my TFS Streets
avatar
Race Ready Fabrications

Posts : 611
Join date : 2010-04-19
Age : 36
Location : Chandler, IN

View user profile

Back to top Go down

Re: Foxbody Front Exit Headers

Post  dr's wife racing on August 8th 2016, 8:36 pm

I wish they were for a heads.
avatar
dr's wife racing
BBF CONTRIBUTOR
BBF CONTRIBUTOR

Posts : 1590
Join date : 2009-08-20

View user profile

Back to top Go down

Re: Foxbody Front Exit Headers

Post  Rickytx630 on August 10th 2016, 5:23 pm

what measurements if you have any yet? were running a D&D K-member. looking for a set of headers that would work with the p51 heads.

Rickytx630

Posts : 34
Join date : 2016-01-18

View user profile

Back to top Go down

Re: Foxbody Front Exit Headers

Post  Race Ready Fabrications on August 10th 2016, 9:52 pm

Rickytx630 wrote:what measurements if you have any yet? were running a D&D K-member.  looking for a set of headers that would work with the p51 heads.

Engine is centered in the frame rails and the oil pan sits 1/2" off the center of the rack. Here are a few more

[/
avatar
Race Ready Fabrications

Posts : 611
Join date : 2010-04-19
Age : 36
Location : Chandler, IN

View user profile

Back to top Go down

Re: Foxbody Front Exit Headers

Post  Coupe Devil on August 11th 2016, 4:55 pm

Do you think they would work with a car setup with motor mounts?
avatar
Coupe Devil

Posts : 202
Join date : 2009-09-25
Age : 38
Location : Conway SC

View user profile

Back to top Go down

Re: Foxbody Front Exit Headers

Post  Race Ready Fabrications on August 11th 2016, 8:28 pm

Coupe Devil wrote:Do you think they would work with a car setup with motor mounts?

No
avatar
Race Ready Fabrications

Posts : 611
Join date : 2010-04-19
Age : 36
Location : Chandler, IN

View user profile

Back to top Go down

Re: Foxbody Front Exit Headers

Post  Race Ready Fabrications on August 11th 2016, 8:31 pm

Coupe Devil wrote:Do you think they would work with a car setup with motor mounts?

No, but I could make you a smoking deal on a motor and mid plate set up off this car too Cool bounce Exclamation
avatar
Race Ready Fabrications

Posts : 611
Join date : 2010-04-19
Age : 36
Location : Chandler, IN

View user profile

Back to top Go down

Re: Foxbody Front Exit Headers

Post  Coupe Devil on August 11th 2016, 11:00 pm

Race Ready Fabrications wrote:
Coupe Devil wrote:Do you think they would work with a car setup with motor mounts?

No, but I could make you a smoking deal on a motor and mid plate set up off this car too Cool bounce Exclamation

Hahah Im not to that point yet with this car. I am sure at some point it will end up with a set of plates and front exit exhaust but not quite yet. My next major project is tubing the front an having teh cage installed. Then im gonna try and enjoy this car for a year or so before I do anything else major.
avatar
Coupe Devil

Posts : 202
Join date : 2009-09-25
Age : 38
Location : Conway SC

View user profile

Back to top Go down

Re: Foxbody Front Exit Headers

Post  jbozzelle on August 13th 2016, 12:36 pm

Definitely won't fit my chassis if your engine is centered...

jbozzelle

Posts : 3341
Join date : 2009-08-10
Age : 43
Location : New Orleans

View user profile

Back to top Go down

Re: Foxbody Front Exit Headers

Post  Race Ready Fabrications on September 5th 2016, 9:55 pm

Sold, pending payment
avatar
Race Ready Fabrications

Posts : 611
Join date : 2010-04-19
Age : 36
Location : Chandler, IN

View user profile

Back to top Go down

View previous topic View next topic Back to top


 
Permissions in this forum:
You cannot reply to topics in this forum