New Guy From CO
Page 1 of 1 • Share •
New Guy From CO
BigBlockMach on September 29th 2010, 10:38 am
Hello everyone. I'm new to the BBF world but I'm a long time ford fanatic! I'm just starting to build my 1st real race car (no street driving)
I will be building a 2003 Mach1. Plan is to run a conventional headed 565 with a F3 123 gear drive setup.
I have read a bunch of great stuff here (Great site). I hope to contribute a little as well.
I will be building a 2003 Mach1. Plan is to run a conventional headed 565 with a F3 123 gear drive setup.
I have read a bunch of great stuff here (Great site). I hope to contribute a little as well.
Last edited by BigBlockMach on October 18th 2010, 8:06 pm; edited 1 time in total
BigBlockMach- Posts: 6
Join date: 2010-09-22 
Re: New Guy From CO
bruno on September 29th 2010, 10:05 pm
f3 on a 565 
...sounds like a wicked build please keep us posted
...sounds like a wicked build please keep us posted _________________
THXS TO ALL MY SPONSORS
www.bfevansraceparts.com
www.evansracingengines.com
JET BOAT BOB
DAN " THE STICKER MAN " HOBBS ...AKA >>>> 56TBIRD
bruno- Moderator
- Posts: 7792
Join date: 2008-12-02
Age: 39
Location: MILLBROOK , AL. -
Re: New Guy From CO
BigBlockMach on September 29th 2010, 10:27 pm
bruno wrote:f3 on a 565
I will do. I plan on taking lots of pictures of the build. I will make a post once we make some progress. Right now I'm striping down the car. I hope to have the suspension and brakes done by the end of the year. If all goes real good I will have the 25.5 welded up by xmas, I already have all the bars ready to go in.
Do you know if there is any way a BBF can fit under a stock hood? Its important to me to keep the Mach 1 look.
BigBlockMach- Posts: 6
Join date: 2010-09-22 -
Re: New Guy From CO
powerstrokeace on October 17th 2010, 12:04 am
Welcome to the forum. Sounds like a killer build. Can't wait to see it. Who's doing the chassis work?
Ace
Ace
powerstrokeace- Posts: 646
Join date: 2009-09-07
Location: colorado -
Re: New Guy From CO
BigBlockMach on October 17th 2010, 10:16 am
powerstrokeace wrote:Welcome to the forum. Sounds like a killer build. Can't wait to see it. Who's doing the chassis work?
Ace
Scott Patten with P&P Performance will be building the car. Staying with a stock suspended car for now.
BigBlockMach- Posts: 6
Join date: 2010-09-22 -
Re: New Guy From CO
dfree383 on October 17th 2010, 11:38 am
Welcomeand get some pics up!! Sounds like it's going to be bad ass
dfree383- BBF CONTRIBUTOR
- Posts: 6749
Join date: 2009-07-09
Location: Everywhere -
Re: New Guy From CO
BigBlockMach on October 18th 2010, 7:37 pm
Thanks guys! I'm excited for this one. It will be a few months before I can post some pics other than a torn apart mustang 
But this winter I hope for a rolling chassis... (25.5, brakes, suspension & rear end)
But this winter I hope for a rolling chassis... (25.5, brakes, suspension & rear end)
BigBlockMach- Posts: 6
Join date: 2010-09-22 -
Re: New Guy From CO
powerstrokeace on October 18th 2010, 7:47 pm
where in Colorado are you located?
Ace
Ace
powerstrokeace- Posts: 646
Join date: 2009-09-07
Location: colorado -
Page 1 of 1
Permissions in this forum:
You cannot reply to topics in this forum