BIG BLOCK FORD
Would you like to react to this message? Create an account in a few clicks or log in to continue.

Dana 60

+7
kjett
10.0
John Myrick
samiam
Mike R
supervel45
cool40
11 posters

Page 3 of 3 Previous  1, 2, 3

Go down

Dana 60  - Page 3 Empty Re: Dana 60

Post  cool40 September 21st 2017, 11:01 pm

Dana 60  - Page 3 Image24
Dana 60  - Page 3 Image22
Dana 60  - Page 3 Image23
cool40
cool40
BBF CONTRIBUTOR
BBF CONTRIBUTOR

Posts : 7307
Join date : 2009-08-31
Age : 53
Location : on the 1/8 mile dyno

Back to top Go down

Dana 60  - Page 3 Empty Re: Dana 60

Post  supervel45 September 16th 2023, 11:00 pm

I am Going To Bump This Thread Cool.

Reason: I was Looking at These Ford Dana and Sterling Axles Lately Myself.

I Got a Non Running Derileck 1980's F250 With a 70U Rear for 5 Bills, 460 Carbed C6 2WD XLT Reg Cab.

I knew The Rearend Was Worth Almost what I Paid.

I put a Battey and A Fresh 600VS Holley on it and a Junk Tire on The Chrome Rim as it Had a Spare on it To get on The Trailer and Back.

Need less to Say it Runs Extremely Well For What it is. Laughing

I sold my/sons Old 1979 F150 4x4 with a High Pinion 44 Open and a Detroit Locked 9" with 38" Swampers 4.56's Granny 4 Spd. for 3.500 Ragged and Beat to The Hilt with a weak non running at the time 351W.

Anyways WTF is Up With This D44 High Pinion Front Open 4:09/1 Geared with a overhaul and some Paint for 3,800 Dollars.

This Guy is Usually Extremely Budget Friendly.

Is This Some Kind of Special UniCorn Now? Suspect

https://www.ebay.com/itm/225650940976?hash=item3489d81c30:g:Xb8AAOSwBnFkolV9

PS: To 83GT He Puts His Number in the Add Also if You go for the F250 Gear or/and Posi Swap on Your New Rig.


Last edited by supervel45 on September 16th 2023, 11:09 pm; edited 2 times in total (Reason for editing : Since I Got one Edit for a Post Edit Collision Might as Well Have 2 and Correct Gramer/Spelling)

supervel45

Posts : 4426
Join date : 2013-09-04

Back to top Go down

Dana 60  - Page 3 Empty Re: Dana 60

Post  cool40 September 16th 2023, 11:02 pm

https://youtu.be/XdobjahOBJQ?si=5epbfKEfsZbwfBx5
cool40
cool40
BBF CONTRIBUTOR
BBF CONTRIBUTOR

Posts : 7307
Join date : 2009-08-31
Age : 53
Location : on the 1/8 mile dyno

Back to top Go down

Dana 60  - Page 3 Empty Re: Dana 60

Post  supervel45 September 16th 2023, 11:06 pm

^LoL Cool Bad Timing You Just Got Me An Edit. I hit Send when You Posted. Crying or Very sad Wink

Well on the D44/HP?

supervel45

Posts : 4426
Join date : 2013-09-04

Back to top Go down

Dana 60  - Page 3 Empty Re: Dana 60

Post  supervel45 September 16th 2023, 11:31 pm

cool40 wrote:Project prostock is coming along slow but still making progress. Painting is about done so now back to building! Dana 60  - Page 3 Image14
Dana 60  - Page 3 Image15


Bump

Pull Video Below

https://www.youtube.com/watch?v=XdobjahOBJQ


Had a Post Collison. Did Not Want The Video Over Looked in The Shuffle.

supervel45

Posts : 4426
Join date : 2013-09-04

Mark Miller likes this post

Back to top Go down

Dana 60  - Page 3 Empty Re: Dana 60

Post  supervel45 September 17th 2023, 2:23 am

Bump For A Good Sunday Video.  Cool









Drive Train Parts/Prices/Availability Updates and Axle/Truck Build and in Racing Action. Cool

Personally I Think The Trucks Kept The BBF's and Parts Development Going Along With Marine Engines Morso-.

Than, Drag Racing Helped but, I Think The Former will Keep it Going and Get More After Market Cast Iron Blocks To Come, Hopefully Soon.

_______________________________________________________________________________________





Also From The Other Thread That Got OffTrack to The Differential Parts at The Active Posts on The Front Page.

If You Have 1998-2011 F-350 or 450 AAM/Dana 14.25" and Want To Lock it Up Cheap and Good Today for $450.00+$25 Shipping or for Re-Sale. Here You Go.

You Could Do It For Under $400.00 if You Bid Also Maybe. Only Has 1 Bid Now.

Not Mine Buyer Shop at Your Own Risk.

https://www.ebay.com/itm/386120378922?_trkparms=amclksrc%3DITM%26aid%3D1110006%26algo%3DHOMESPLICE.SIM%26ao%3D1%26asc%3D20201210111314%26meid%3Dec22535110914836be222d866aa0745e%26pid%3D101195%26rk%3D3%26rkt%3D12%26sd%3D186013812883%26itm%3D386120378922%26pmt%3D1%26noa%3D0%26pg%3D4429486%26algv%3DSimplAMLv11WebTrimmedV3MskuWithLambda85KnnRecallV1V2V4ItemNrtInQueryAndCassiniVisualRankerAndBertRecallWithVMEV3CPCAuto%26brand%3DDetroit&_trksid=p4429486.c101195.m1851&amdata=cksum%3A386120378922ec22535110914836be222d866aa0745e%7Cenc%3AAQAIAAABYObhgc4Nk8%252BdtAwOww4FKLaj%252FQ5qqgDlQCuqZA43WcPFUWDERCUugbbOk7XQv0JXlBfqCg2xKF3WcPghxGMFw2oSlXvfExEaMYr7I7LmrHcP6czY1wIMt0ORyKiCWt95xldincyyBx3g%252BNDW%252B%252FhWUgTaBhK6xAm%252BJIbCOMehu%252BdwKoxoxchzl3HUFZp4nUx0oMxTrqcCZ2auwsdgzZlJ1DLJCNrmbO%252FAzu50ixXeNSxLGTB7iBtqFnEAuhuPN84wB9gEEs3uJdXr30wY%252F8%252FiQCSaRxgoV2MZ05W6eUXCQKLRzyNu2OedIj86812RlQpOm6mmd%252Bv7SoRqmphEdMSeuDZLQ%252F2Z1W8l10K3Dj%252Fh7YfKALa11USgvgDInNURWgfoJQcRZTmoCkB5TahgNTgVA78kJV9Dr8zP0MWf1AVVPxB%252BpFC%252FHe5klYceNmhDbg6tUaa1rtYjPEpEjyxa9mpO%252FBg%253D%7Campid%3APLX_CLK%7Cclp%3A4429486&epid=2333766655

Detroit Locker New Part # 250SL166 New.

List price. 895.00 Jeg's

https://www.jegs.com/i/Detroit-Locker/357/250SL166/10002/-1

Page 10 Application. Ford

https://www.eaton.com/ecm/groups/public/@pub/@eaton/@per/documents/content/ct_128302.pdf

I Really am Temped Not To Let This One Go.

supervel45

Posts : 4426
Join date : 2013-09-04

Back to top Go down

Dana 60  - Page 3 Empty Re: Dana 60

Post  supervel45 September 20th 2023, 12:04 pm

^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^

pirat pirat pirat pirat pirat pirat pirat pirat PIRATE pirat pirat pirat pirat pirat pirat pirat pirat

To Any of The 4x4 Types Running The Big Trucks With Agg.orTractor Tires That Come Across Above Locker!

It's The Long Text. FleeBay Link I Mentioned Directly Above!!! It's for a Ford F350 to F550 Chasis Cab Rare Limited Differential. It's a Giant One That Looks Like a 9" Ford without the Seperate Pinion Unit.

It is a Rare Unit Used for a While in The Most Super Extra Duty Rigs. Think U-Haul and The Like.

It's a Ford/Dana S135 Series.

I Would Skip it. If It's Too Good To Be True it Likely Is.

The Other Detroit Locker FleeBay Links in This Thread are Good Long Time FleeBayers and or Legit as Far as I Know.

That Last I would Highly Recommend Skipping. Evil or Very Mad

Like I Always Say Buyer do Your Homework and be Extremely Aware of Scammers. They are Much Worse Now!

supervel45

Posts : 4426
Join date : 2013-09-04

Back to top Go down

Dana 60  - Page 3 Empty Re: Dana 60

Post  supervel45 September 20th 2023, 10:10 pm

This is what I mentioned About The Industrial Military Contract Stuff Cool.

Notice the Part #'s Some One Scribed on The Side. It's Likely Wrong.

Notice the Diameter of The Short Fat Hubs and How Thick The Bearing Mount Is.

Lets Go with The 40 Spline Count is Correct. I Would Not be Surprised That It Was.

Also Note On The Back of The Ring Gear Pads The 4 Extra Thick Ribs That Form an Narrow X.

Sure You Might Bore a 70 or Some Kind of 60 or an 80 and make it Work?

You Gotta Watch The OddBall Used Stuff Around These. It's All Over The Place With Dana/Spicer Parts.

https://www.ebay.com/itm/325640609497?hash=item4bd1b15ed9%3Ag%3AppgAAOSwEixkUa7n&amdata=enc%3AAQAIAAAA4AODujT7Sv2fbMzlLs5VazbCeLHqC8WQoi1EMzXdl8TA3W6c8QlVzsf10kKY4uj8iGKadk%2BCNed1vPoqNJIl6j%2B30NyC3vDTk6CA5JSAiIMK0MkwnBwTa%2BfbLsT6KubVWlIz43Lo6xhJWhXA%2FHs1xgJweEdQVD1Bug2sllfE0QwP2XOxx2DpJRlrEwi5zKbXSrS8uF7dbbE4ApTIoOV7YqKZxC%2FM3R5wRzdKFeZ0YlZRrjIN0v8HXzhc8YWa3aWCNeekabg269nEIa8%2FZyHDVnSoNiEBH4InmUFZYrZNEVoj%7Ctkp%3ABk9SR5LXvtbWYg&LH_All=1

^Note Not Mine and Nothing to do With It.^ Always Do Your Homework and Shop at Your Own Risk.

Just Using it as an Example.

It's Marked

186
SL58C
70925
29.F.09
41

^At Least That's What it Looked Like Under a Magnfier Mouse.

All The Bigish Light Detroit Stuff is 225 Series and Up Number Wise. The Biggest Axle I believe 2.75", as Far As I have Seen and If Memory Serves 54 spline. I believe it was a 450S Series.




supervel45

Posts : 4426
Join date : 2013-09-04

Back to top Go down

Dana 60  - Page 3 Empty Re: Dana 60

Post  supervel45 September 25th 2023, 2:57 pm

^ Never Say Never, LoL. Suspect Also Edit The Above Link Info to: Second Line: SL58B. I musta mistyped. Embarassed

New Dana 70 40 Spline Detroit Lockers Availiable, It Appears. Smile

Looks Like It's for a 70U 4.10 and Down. I Could Not Find a 4.56 and Up. First I have Heard of Them, also.

https://www.4wheelparts.com/p/eaton-detroit-locker-dana-70u-40-spline-4-10-down-automatic-locker-225sl205a/_/R-BHXC-225SL205A?ppcfon=1&gp=1&&ecmp=s:google_18142422611___&utm_source=google&utm_medium=cpc&utm_campaign=SC%20Shopping%20-%20Top%20&%20Performers%20-%20Performance%20Max&gclid=CjwKCAjw38SoBhB6EiwA8EQVLr6H6KFxg5yaSdLn-QTBupymecOz0hkiYrqe0A4tvC669YY8ERk7pxoCfgAQAvD_BwE&gclsrc=aw.ds






Dana 70 37 Page Thread. Have Fun.


https://www.pirate4x4.com/threads/the-dana-70-thread.522333/

supervel45

Posts : 4426
Join date : 2013-09-04

Back to top Go down

Dana 60  - Page 3 Empty Re: Dana 60

Post  supervel45 November 12th 2023, 9:39 am

Hey Cool, Can You, Or any of your 4X4 Buddies Come Up with a Dana 60 Power Loc 4 Pinion Posi Carrier? Question

Don't Need the Internals and a Junk One is Fine, If The Case is Still Good (Not Cracked).

4.10 and Down or 4.56 and Up. Either Will be Fine.

Yes I know they are Heavy and the Ride Won't be Cheap. Cool


supervel45

Posts : 4426
Join date : 2013-09-04

Back to top Go down

Dana 60  - Page 3 Empty Re: Dana 60

Post  supervel45 November 16th 2023, 2:32 am

cool40 wrote:
supervel45 wrote:http://www.ebay.com/itm/D70-HD-DETROIT-LOCKER-NEW-SURPLUS-/272151292775?hash=item3f5d7b2b67:g:vhQAAOxywh1TBMwc&vxp=mtr                If you can use it or want it, here it is under best offer. He also has a lot of other differential parts.
thanks for the tip! Cool Wink  Dana 60  - Page 3 20160310_154559

Another Dana 70 Detroit Locker 35 Spline Just Popped up on FleeBay.

It's a MAKE OFFER DEAL ALSO!!! UNDER 500 Cool

Anyways Just Passing It On For You

https://www.ebay.com/itm/335119049106?epid=1117820528&hash=item4e06a6e192:g:TZ4AAOSwIxtlTqN9&amdata=enc%3AAQAIAAAA0Nu%2BUV%2ByzocIbXode385oOAekPkeBT1e2kDrS0sPRx7U9PqWtCLlHItaz%2F%2BMSJhooO%2BjqWDuv3lm0YPkKjnEZZ6bNtgQ2XxoIQFyPwDJeJlmBHITgEVGWuM5JPGYw00v5lvlxp9mQ0x7I29YUy1%2BmFfD5H3kPnCltoAAYGmN3txreJ3A9xt32YpXriFBrxXHJkUwbQceNec%2FRYjhuKznjOJ8XqL47Ac%2Flq%2BTRijMGlq88BaD%2BMvtFxf%2B5RCO9cJLNsQDoRVugt0%2F67dKqlr3%2FD4%3D%7Ctkp%3ABk9SR5yv1ez6Yg

I Have Something Going in That Direction for My 60. Need Some 35 Spine Sides Out of a Blown Up 60 DL.

Hook A Brother Up If You Can.

I Let a New 60 DL Gut Unit Go For 125, 35 Spline Like a Dummy. Now I am Kinda Screwed.Sad

Spool On The Way Though, 110 Plus Ttl. Cool

I Am Setting Up 4.10 and A 4.56 Combo on The 4 Link, Or at Least Trying Smile Arrow

PS1: That DL 70 Unit Is FREE SHIPPING, ALSO Cool Very Happy

PS2: The DL 70 Unit I Just Linked, Looks Like It is For 4.10 and Lower Numerically Lower Gears.

A Spacer Can Be Made For Lower (Higher Numerically) Gears and Attached To Be Strong. Not Very Conventional But, It Won't Go Any Where When Done. Not Going to Say Any More on the Open Forum Though About How.

PS3: The Linked DL70 is Deffinently a "Soft Locker". You Can See The ADDED DISC.'s When You Look Through The AXLE HOLES From THE SIDE.

supervel45

Posts : 4426
Join date : 2013-09-04

Back to top Go down

Dana 60  - Page 3 Empty Re: Dana 60

Post  Sponsored content


Sponsored content


Back to top Go down

Page 3 of 3 Previous  1, 2, 3

Back to top

- Similar topics

 
Permissions in this forum:
You cannot reply to topics in this forum