Parting out 545
+4
seanb
wickettoby1
duff429
BuckeyeBOSS
8 posters
Page 1 of 1
Parting out 545
SOLD
545 cid Big Block Ford longblock.
Engine was a fresh rebuild that wiped the tip of a cam lobe within a few dozen miles of being rebuilt. So it should be disassembled, cleaned, and rebuilt again with a new cam. $800 in port job of these heads alone. Naturally aspirated on pump gas, it's about 11:1 compression.
Here's what you get:
Engine:
-545 cid shortblock - a .030 over factory D1VE block, forged 4.5" crank from AD Performance, 6.8" scat h-beam rods, ARP 2000 series rod bolts, dished forged Diamond pistons with custom valve reliefs for both Kaase P-51 and conventional heads, Total Seal plasma moly file fit rings, Clevite H series bearings, Durabond cam bearings, sfi flexplate, sfi balancer, internally balanced
-1969 DOVE-C heads, ported - 2.250 intake valves and 1.720 exhaust.
-Custom Bullet Racing Solid Flat Tappet cam - 260/269 @ .050, 640/640 lift (WIPED LOBE)
-Roller rockers
-Chrome valve covers
-March aluminum crank pulley (stock size 5.0L) and alternator pulley and belt
-Stock 429 oil pan
-Spark plugs
-SFI flexplate
-SFI balancer
-The intake manifold in the pics has been sold.
$3000 for everything listed above. Willing to sell just the shortblock for $2200. I prefer you pick it up (just north of Columbus, Ohio), as I was quoted $800 from Ohio to Florida for shipping/packaging with lift gate service at both ports.
Meziere electric water pump (#WP108S) WITH backing plate - both black anodized. Bolts included. $325 shipped to the lower 48
Custom API 9" 4500 rpm stall converter for Ford C6 tranny. Excellent shape, ran flawlessly in my 69 Mustang. Believe it has the small pilot. $325 shipped to the lower 48
545 cid Big Block Ford longblock.
Engine was a fresh rebuild that wiped the tip of a cam lobe within a few dozen miles of being rebuilt. So it should be disassembled, cleaned, and rebuilt again with a new cam. $800 in port job of these heads alone. Naturally aspirated on pump gas, it's about 11:1 compression.
Here's what you get:
Engine:
-545 cid shortblock - a .030 over factory D1VE block, forged 4.5" crank from AD Performance, 6.8" scat h-beam rods, ARP 2000 series rod bolts, dished forged Diamond pistons with custom valve reliefs for both Kaase P-51 and conventional heads, Total Seal plasma moly file fit rings, Clevite H series bearings, Durabond cam bearings, sfi flexplate, sfi balancer, internally balanced
-1969 DOVE-C heads, ported - 2.250 intake valves and 1.720 exhaust.
-Custom Bullet Racing Solid Flat Tappet cam - 260/269 @ .050, 640/640 lift (WIPED LOBE)
-Roller rockers
-Chrome valve covers
-March aluminum crank pulley (stock size 5.0L) and alternator pulley and belt
-Stock 429 oil pan
-Spark plugs
-SFI flexplate
-SFI balancer
-The intake manifold in the pics has been sold.
$3000 for everything listed above. Willing to sell just the shortblock for $2200. I prefer you pick it up (just north of Columbus, Ohio), as I was quoted $800 from Ohio to Florida for shipping/packaging with lift gate service at both ports.
Meziere electric water pump (#WP108S) WITH backing plate - both black anodized. Bolts included. $325 shipped to the lower 48
Custom API 9" 4500 rpm stall converter for Ford C6 tranny. Excellent shape, ran flawlessly in my 69 Mustang. Believe it has the small pilot. $325 shipped to the lower 48
Last edited by BuckeyeBOSS on October 14th 2018, 10:54 am; edited 8 times in total
BuckeyeBOSS- Posts : 26
Join date : 2017-05-17
Re: Parting out 545
Pm sent
duff429- Posts : 202
Join date : 2009-08-20
Age : 39
Location : Wyoming/ North Dakota
Re: Parting out 545
What brand crank? Was there any damage to it when the cam lobe got eaten?
wickettoby1- Posts : 352
Join date : 2016-02-02
Location : SE Michigan
Re: Parting out 545
AS Performance crank. Motor hasn't been torn down yet.
BuckeyeBOSS- Posts : 26
Join date : 2017-05-17
Re: Parting out 545
Sorry, google doesn't know, can I ask who AS performance is?
Are you willing to ship the motor?
Are you willing to ship the motor?
seanb- Posts : 2
Join date : 2018-08-02
Re: Parting out 545
Sorry, AD Performance here: http://www.adperformance.com
I was quoted $800 shipping and packaging from Ohio to Florida for the long block, that's with insurance and lift gate service at both ends.
I was quoted $800 shipping and packaging from Ohio to Florida for the long block, that's with insurance and lift gate service at both ends.
BuckeyeBOSS- Posts : 26
Join date : 2017-05-17
Re: Parting out 545
Carb and accessories sold. Thanks wickettoby1, good to meet you!
BuckeyeBOSS- Posts : 26
Join date : 2017-05-17
Re: Parting out 545
BuckeyeBoss is an honest seller and a nice guy too boot, i would buy from him again.
Last edited by wickettoby1 on August 13th 2018, 8:13 pm; edited 1 time in total
wickettoby1- Posts : 352
Join date : 2016-02-02
Location : SE Michigan
Re: Parting out 545
On the torque converter- what does API stand for? Couldn’t find anything on it. Or was that a typo ? Also are the feet set for standard location or set out for use with mid plate?
stanger68- Posts : 502
Join date : 2015-12-05
Location : Birmingham, Al
Re: Parting out 545
Api Racing Transmissions & Torque Converters was the company, I believe out of Canada.
Not sure about the feet. Is there a picture or measurement I can take for you?
Not sure about the feet. Is there a picture or measurement I can take for you?
BuckeyeBOSS- Posts : 26
Join date : 2017-05-17
Re: Parting out 545
Feet appear to be threaded in the pic so I could just use a spacer thats not a big deal. Will have to do some more digging later on the api part. Never heard of them that’s all. Thanks for the quick response.
stanger68- Posts : 502
Join date : 2015-12-05
Location : Birmingham, Al
Re: Parting out 545
Holy crap! $800 to Florida, I'm near Seattle which is twice the distance, the money I'm saving on this just goes into shipping. Good luck on the sale, this looks like a good deal to me, I'm just too far away!
seanb- Posts : 2
Join date : 2018-08-02
Re: Parting out 545
I’ll take the intake if you still have it. I tried to pm you but not sure if it sent.
You can reach me 6154769100.
Thanks,
Frank
You can reach me 6154769100.
Thanks,
Frank
738drvr- Posts : 600
Join date : 2010-02-15
Age : 59
Location : Middle Tennessee
Re: Parting out 545
You interested in selling the short block only?
biglucky- Posts : 213
Join date : 2012-11-04
Age : 67
Location : Shepherdsville, ky
Re: Parting out 545
biglucky wrote:You interested in selling the short block only?
Yes I would. Please PM me with the specific parts you would want included, obviously the block, crank, rods, and pistons, I'd like to keep the oil pan on there to protect the crank, too.
BuckeyeBOSS- Posts : 26
Join date : 2017-05-17
Re: Parting out 545
BuckeyeBOSS i sent you a pm.
biglucky- Posts : 213
Join date : 2012-11-04
Age : 67
Location : Shepherdsville, ky
Re: Parting out 545
racerfrank wrote:Are the heads ported to scj/cj size or standard?
Frank
Here's what I got back from the engine builder on the heads: "They have some port work done. I can't remember if they were opened up to CJ size."
BuckeyeBOSS- Posts : 26
Join date : 2017-05-17
Heads
Thank you. I asked because I have a new set of headers for the standard head and dont want to have to purchase another
set of headers if I can help it.
Frank
set of headers if I can help it.
Frank
racerfrank- Posts : 2
Join date : 2012-12-11
Re: Parting out 545
Updated pricing and OP with parts that are still left. Thanks guys.
BuckeyeBOSS- Posts : 26
Join date : 2017-05-17
Similar topics
» Parting out '76 Cobra II
» parting out 68 galaxie
» FS: parting out 1967 galaxia 500 (phx AZ)
» Parting out 1987 F250 4x4
» 1977 Ford Bronco Parting Out! SOLD
» parting out 68 galaxie
» FS: parting out 1967 galaxia 500 (phx AZ)
» Parting out 1987 F250 4x4
» 1977 Ford Bronco Parting Out! SOLD
Page 1 of 1
Permissions in this forum:
You cannot reply to topics in this forum