Baller 466" build.
+13
QtrWarrior
John Myrick
67mustang
Dave C.
Nevs
cool40
bbf-falcon
85bigblockfox
Mustang-junky
dfree383
schmitty
bruno
richter69
17 posters
Page 1 of 3
Page 1 of 3 • 1, 2, 3
Baller 466" build.
Been gathering parts for a couple months now for this deal, I'll try and put a dollar amount on stuff as damn near every part has been a trade, or two, or three lol.
Fully prepped D9 block......little brother traded this for some smallblock stuff he had like 10 years ago........free
I had a cast 4.5 crank I aquired in another trade, no real money in it, I swapped it to a buddy who gave me in return the following:
I new set of Speed Pro 2443's....030 over, one new set of Eagle H beams w the std bolts, a complete set of ARP head bolts w washers, a stock oil pan, an ext balance crank... .010/ .010, with new rod and main bearings, harmonic balancer-stock, waterpump-stock, flexplate-stock, a large box of misc bolts including a Ford Racing one piece fuel pump eccentric......... complete Holley 850 dp, 1" phenolic spacer.....this stuff was give to him......so free
I'm getting a stock set of valve covers, timing cover, hatchet weight, from another buddy here local.....free
The same buddy I'm gonna go through a C6 for him.......in exchange I got a set of ported Dove-c heads w stainless 2.19/1.76 valves, studes and guideplates, has roller springs and molly retainers I wont use. Actual dollar amount invested 300.00
I traded an expansion tank I made, I had approx 15.00 bucks of material in, I made a trip south to sell some Nos parts to a guy so I had the guy wanting the tank meet me at the same place, swapped a nice 8012 Stealth intake for the tank.
I bought a carb and intake off of a local swap shop deal on the radio here, paid 130 for a carb 'll use on something else and the sbc intake was a freebie.....traded the parts manager here it for a reman duraspark in return......free
Swapped a bunch of CO2 bottles and regs and a t stop solenoid for a nice FT cam, lifters, springs, retainers and locks. The CO2 stuff was a sponsorship deal from a long time ago, Im out some lettering I had done..by another buddy who did it for free.........so no real money...other than the 75.00 I gave as boot for the cam stuff.
swapped a sbf stud girdle and posilocks I had a 100 dollar value on for a FRP billet chain set already double pinned, a bronze thrust plate and a hardned oilpump shaft. so 100 bucks
set of 15 Harland Sharp rockers, swapping a set of HS sbf rockers, 150.00 value
found 1 more rocker, price yet to be determined....
I have a damaged Kasse oilpump that was give to me, I need to buy a melling pump to rob the gears out of......to be updated
I traded a set of pushrods for my old set of Trick Flow 3/8 pushrods I gave away in a previous trade.........so free
MSD 6 AL and Blaster coil..........set of 3.5" Magnaflow race mufflers...........given to me by a friend whom I'm doing some chassis work, which I was gonna do free anyway.......so "free" again.
I have a pickup tube kit for the oilpan I had lying around from where I have no idea...........free
make it an even 100 bucks for shipping cost etc....so 740 bucks total so far...........
Think thats about it. I need:
oil filter
rings
gasket set
mech fuel pump
cap and rotor
rebuild kit for carb
I'll buy that stuff new (mybe not the fp if i can find one)
may be a pump gas deal, if i do I will have a buddy machine the domes.....again for free lol. May do E85 if I do I'll barter for a carb or something............may be a few months before I get started on this but when I do, I'll be sure and do a burnout....................
Fully prepped D9 block......little brother traded this for some smallblock stuff he had like 10 years ago........free
I had a cast 4.5 crank I aquired in another trade, no real money in it, I swapped it to a buddy who gave me in return the following:
I new set of Speed Pro 2443's....030 over, one new set of Eagle H beams w the std bolts, a complete set of ARP head bolts w washers, a stock oil pan, an ext balance crank... .010/ .010, with new rod and main bearings, harmonic balancer-stock, waterpump-stock, flexplate-stock, a large box of misc bolts including a Ford Racing one piece fuel pump eccentric......... complete Holley 850 dp, 1" phenolic spacer.....this stuff was give to him......so free
I'm getting a stock set of valve covers, timing cover, hatchet weight, from another buddy here local.....free
The same buddy I'm gonna go through a C6 for him.......in exchange I got a set of ported Dove-c heads w stainless 2.19/1.76 valves, studes and guideplates, has roller springs and molly retainers I wont use. Actual dollar amount invested 300.00
I traded an expansion tank I made, I had approx 15.00 bucks of material in, I made a trip south to sell some Nos parts to a guy so I had the guy wanting the tank meet me at the same place, swapped a nice 8012 Stealth intake for the tank.
I bought a carb and intake off of a local swap shop deal on the radio here, paid 130 for a carb 'll use on something else and the sbc intake was a freebie.....traded the parts manager here it for a reman duraspark in return......free
Swapped a bunch of CO2 bottles and regs and a t stop solenoid for a nice FT cam, lifters, springs, retainers and locks. The CO2 stuff was a sponsorship deal from a long time ago, Im out some lettering I had done..by another buddy who did it for free.........so no real money...other than the 75.00 I gave as boot for the cam stuff.
swapped a sbf stud girdle and posilocks I had a 100 dollar value on for a FRP billet chain set already double pinned, a bronze thrust plate and a hardned oilpump shaft. so 100 bucks
set of 15 Harland Sharp rockers, swapping a set of HS sbf rockers, 150.00 value
found 1 more rocker, price yet to be determined....
I have a damaged Kasse oilpump that was give to me, I need to buy a melling pump to rob the gears out of......to be updated
I traded a set of pushrods for my old set of Trick Flow 3/8 pushrods I gave away in a previous trade.........so free
MSD 6 AL and Blaster coil..........set of 3.5" Magnaflow race mufflers...........given to me by a friend whom I'm doing some chassis work, which I was gonna do free anyway.......so "free" again.
I have a pickup tube kit for the oilpan I had lying around from where I have no idea...........free
make it an even 100 bucks for shipping cost etc....so 740 bucks total so far...........
Think thats about it. I need:
oil filter
rings
gasket set
mech fuel pump
cap and rotor
rebuild kit for carb
I'll buy that stuff new (mybe not the fp if i can find one)
may be a pump gas deal, if i do I will have a buddy machine the domes.....again for free lol. May do E85 if I do I'll barter for a carb or something............may be a few months before I get started on this but when I do, I'll be sure and do a burnout....................
richter69- Posts : 13649
Join date : 2008-12-02
Age : 53
Location : In the winners circle
Re: Baller 466" build.
I DONT CARE WHAT YOU SAY THAT IS A BALLER BUILD !!!!!
_________________
coming soon x275 build .........
thanks to all my sponsors :
www.OakleyMotorsports.com
www.Induction-Solutions.com
www.bfevansraceparts.com
www.ultimateconverter.com
www.keithfulpmotorsports.com
Re: Baller 466" build.
Low Baller
schmitty- Posts : 4538
Join date : 2008-12-02
Age : 54
Location : Holdrege, NE
Re: Baller 466" build.
Needs to change the title to Baller 466......
dfree383- BBF CONTRIBUTOR
- Posts : 14853
Join date : 2009-07-09
Location : Home Wif Da Wife.....
Re: Baller 466" build.
Subscribing. Looking forward to the results.
Jess
Jess
Mustang-junky- Posts : 438
Join date : 2011-12-04
Location : Central New York. The state, not the city.
Re: Baller 466" build.
hell yeah I like it!! ..........
richter69- Posts : 13649
Join date : 2008-12-02
Age : 53
Location : In the winners circle
Re: Baller 466" build.
never been really good at retaining info , but did i miss what car this is going into ???
_________________
coming soon x275 build .........
thanks to all my sponsors :
www.OakleyMotorsports.com
www.Induction-Solutions.com
www.bfevansraceparts.com
www.ultimateconverter.com
www.keithfulpmotorsports.com
Re: Baller 466" build.
plans are for my wifes 64 swb truck, c6, good rearend stuff, just something to beat around town in....... i miss not having a street ride of sorts. It will be a long term project but the engine build will start after I get the 81 back together. Hell if I hurt DD it may go in the Grande' ........
richter69- Posts : 13649
Join date : 2008-12-02
Age : 53
Location : In the winners circle
Re: Baller 466" build.
update
85bigblockfox- Posts : 241
Join date : 2013-01-02
Location : Land of big gals and big ( . )( . )
Re: Baller 466" build.
pile of shit
richter69- Posts : 13649
Join date : 2008-12-02
Age : 53
Location : In the winners circle
Re: Baller 466" build.
Pics of said shit?
dfree383- BBF CONTRIBUTOR
- Posts : 14853
Join date : 2009-07-09
Location : Home Wif Da Wife.....
Re: Baller 466" build.
go look at the run stand pic, thats it pretty much lol.
I gotta lotta irons in the fire right now, i have nearly all the parts I just need time to dick with it, which i don't have right now.
This summer.....
I gotta lotta irons in the fire right now, i have nearly all the parts I just need time to dick with it, which i don't have right now.
This summer.....
richter69- Posts : 13649
Join date : 2008-12-02
Age : 53
Location : In the winners circle
Re: Baller 466" build.
Sounds very similar to my 514 Baller build for the Foxbody
bbf-falcon- Posts : 8995
Join date : 2008-12-03
Location : Jackson, Ohio
Re: Baller 466" build.
bump for a good deal
cool40- BBF CONTRIBUTOR
- Posts : 7315
Join date : 2009-08-31
Age : 53
Location : on the 1/8 mile dyno
Re: Baller 466" build.
add a torker II intake, a 8082 dominator, and a set of scj alum valve covers, added cost...... about 300 bucks.
richter69- Posts : 13649
Join date : 2008-12-02
Age : 53
Location : In the winners circle
Re: Baller 466" build.
This thread is useless with out pics of the junk.......
dfree383- BBF CONTRIBUTOR
- Posts : 14853
Join date : 2009-07-09
Location : Home Wif Da Wife.....
Re: Baller 466" build.
dfree383 wrote:This thread is useless with out pics of the junk.......
Says the guy who still hasn't posted pics of the hot Asian girls...
Nevs- BBF CONTRIBUTOR
- Posts : 2724
Join date : 2009-02-07
Age : 70
Location : NW Iowa(Odebolt)
Re: Baller 466" build.
dfree383 wrote:This thread is useless with out pics of the junk.......
back burner project.
richter69- Posts : 13649
Join date : 2008-12-02
Age : 53
Location : In the winners circle
Re: Baller 466" build.
still in a pile.... of shit
richter69- Posts : 13649
Join date : 2008-12-02
Age : 53
Location : In the winners circle
Re: Baller 466" build.
Start it and do a burnout!!!
67mustang- Posts : 43
Join date : 2013-03-10
Location : Oklahoma
Re: Baller 466" build.
tank tracks
richter69- Posts : 13649
Join date : 2008-12-02
Age : 53
Location : In the winners circle
Re: Baller 466" build.
Snail Tracks......
dfree383- BBF CONTRIBUTOR
- Posts : 14853
Join date : 2009-07-09
Location : Home Wif Da Wife.....
Re: Baller 466" build.
richter69 wrote:tank tracks
I see the complication...
Start it and make sparks!!!
67mustang- Posts : 43
Join date : 2013-03-10
Location : Oklahoma
Re: Baller 466" build.
My smallblock will be done first, beggining to think I should have used a different machine shop......
richter69- Posts : 13649
Join date : 2008-12-02
Age : 53
Location : In the winners circle
Page 1 of 3 • 1, 2, 3
Similar topics
» E4OD build reccomendations for a 79 f150... first transmission build, no ideah what I'm doing
» Cam help 572 a460 build street/strip build
» Build help 4.3 or 4.5 stroke street/strip build
» TFS 521 build
» 408/418W build... what would you build?
» Cam help 572 a460 build street/strip build
» Build help 4.3 or 4.5 stroke street/strip build
» TFS 521 build
» 408/418W build... what would you build?
Page 1 of 3
Permissions in this forum:
You cannot reply to topics in this forum